For factories, warehouses and commercial buildings, electricity is often one of the largest operating costs. Rooftop solar can reduce that cost substantially, but businesses face an early decision: buy the plant outright, or let a developer install and own it while the business pays only for the units consumed. These are known as the CAPEX and OPEX (or RESCO) models. Each suits different financial situations. This guide compares them so that owners and finance teams can choose with confidence.
1. The CAPEX model: you own the plant
In the CAPEX model, the business pays for the design, equipment and installation, and owns the plant from day one. All the savings on electricity bills belong to the business.
- Highest long-term savings, because there is no developer margin.
- Possible tax benefits such as depreciation, subject to current tax rules — confirm with your tax adviser.
- The business carries the operation, maintenance and performance risk, usually managed through an AMC.
- Requires upfront capital or a loan; see solar financing options from ATTPL Finance.
2. The OPEX / RESCO model: pay per unit
In the OPEX model, a renewable energy service company (RESCO) invests in the plant, installs it on your roof and maintains it. You sign a long-term power purchase agreement (PPA) and pay a fixed or escalating tariff per unit generated, usually lower than the grid tariff.
- No upfront investment and no maintenance responsibility.
- Savings start immediately, but are lower than in the CAPEX model.
- Long contract periods with conditions on roof access, minimum offtake and exit.

3. Comparing the two
- Cash position: businesses with strong cash flow or access to cheap finance usually prefer CAPEX; those wanting to preserve capital often choose OPEX.
- Roof ownership and tenure: OPEX contracts need a long, secure right to use the roof. Rented premises may make this difficult.
- Consumption pattern: both models work best where daytime consumption is high, as in most factories.
- Risk appetite: under OPEX, the developer takes performance risk; under CAPEX, you do, backed by warranties.
4. Technical checks for any model
Before signing, get a structural assessment of the roof, a shadow analysis and a load study. Industrial sheds need checks on purlin capacity and sheet condition, and roofs should be waterproofed or repaired before installation. Our industrial rooftop solar planning guide explains these steps, and ATTPL Infra’s waterproofing guide covers roof preparation.
5. Contract points to review
- Tariff, escalation and how units are measured.
- Contract length, early exit terms and buy-out options.
- Responsibility for roof repairs and temporary removal of panels.
- Performance guarantees, insurance and what happens if the plant under-performs.
- Compliance with state net-metering or open-access rules.
Long-term contracts deserve legal review; ATTPL Legal can help.
6. Make the decision with numbers
Model the cash flows over the plant life for both options: upfront cost, loan repayments, savings, maintenance, inverter replacement and tax effects for CAPEX; tariff payments and savings for OPEX. Compare payback, net present value and the effect on your balance sheet. The ATTPL Group article on reducing factory energy costs shows how solar fits with wider efficiency measures.
7. Hybrid approaches and phasing
The choice is not always all-or-nothing. Some businesses start with an OPEX plant on one roof and add a CAPEX plant later as cash flow allows, or own the plant on their main factory while using a developer for leased warehouses. Others take a loan for a CAPEX plant so that EMI payments are covered by the monthly savings. Phasing also lets you learn how solar performs on your site before scaling up.
- Plan the full roof layout first, even if you build in phases.
- Size the system to your daytime consumption and the applicable regulations.
- Keep space for inverters, cabling and safe maintenance access.
Energy audits often reveal quick savings — lighting, compressed air leaks, motor efficiency — that should be addressed alongside solar.
Frequently asked questions
Which model gives higher savings?
CAPEX usually gives higher lifetime savings because the business keeps all the benefit, but it needs upfront capital.
Can a factory on rented premises go solar?
Yes, but OPEX contracts need long-term roof access, so the landlord’s consent and lease terms are important.
Who maintains the plant under OPEX?
The developer is normally responsible for operation and maintenance under the PPA.
Evaluating solar for your factory? Contact ATTPL Solar for a site assessment.



